portroom.blogg.se

Trex miner lhr
Trex miner lhr









trex miner lhr
  1. #Trex miner lhr how to#
  2. #Trex miner lhr 1080p#
  3. #Trex miner lhr driver#
  4. #Trex miner lhr full#
  5. #Trex miner lhr windows#

does not take any responsibilities related to overclocking or performing any adjustments to your computer. Of course, use overclocking at your own risk! This will void the warranty of your graphics card, and may even destroy it, or damage its components. The settings we are about to show you can be applied both to the first generation RTX 3060 cards, as well as to the second generation RTX 3060 (LHR) cards. Best Overclock Settings for Mining Ethereum with GeForce RTX 3060īefore you attempt to mine Ethereum with you GeForce RTX 3060, we strongly recommend overclocking the card in order to achieve the highest possible hashrate, and lower the card’s power consumption as much as possible.

#Trex miner lhr how to#

To find out how to squeeze the maximum performance out of your GeForce RTX 3060 card, keep reading further. But with a few tweaks and proper mining software, you can push your card up to 47 MH/s mark. However, if you own a second generation RTX 3060 (LHR) that has a GA106-302 chip, then you’ll have to settle with a 21-23 MH/s mining hashrate. This will allow you to mine Ethereum at hashrate of 45-50 MH/s.

#Trex miner lhr driver#

If you own a first generation RTX 3060 card that has a GA106-300 chip, then you can easily bypass the built-in limiter by simply installing the 470.05 driver which unlocks the card for mining Ethereum. These miners fully bypass the card’s built-in mining limiter, thus allowing the card to achieve its maximum mining speed. However, the built-in limiter only affects Ethereum mining performance, which means you can mine other cryptocurrency coins without any issues.Īs of May 7th 2022 all LHR cards can now be fully unlocked! If you plan to mine Ethereum with the RTX 3060 LHR we strongly recommend using the latest version of NBMiner or NiceHash QuickMiner. Unfortunately, most GeForce RTX 3060 graphics cards come with a built-in crypto mining limiter which nerfs the card’s performance while mining Ethereum. Read also: Best GeForce RTX 3060 Ti LHR Overclock Settings for Mining Ethereum

#Trex miner lhr 1080p#

But besides being great for high FPS gaming at 1080p or 1440p resolution, this card is also well-suited for mining cryptocurrencies such as Ethereum (ETH) or other coins like Ravencoin (RVN) and ERGO (ERG).

trex miner lhr

  • Try reducing memory overclock of the GPU that frequently trips LHR.Thanks to its 3,584 CUDA cores and 12GB of VRAM, the GeForce RTX 3060 is a graphics card that has brought next-gen shading and ray-tracing performance to masses.
  • Do not delay applying overclock - this will mess up calibration results and the miner will display unrealistically high LHR tune values.
  • Avoid using RDP if it puts load on your LHR cards.
  • Make sure you don't have monitors connected to your LHR cards, or at least turn them off during miner start up to let it calibrate correctly.
  • #Trex miner lhr windows#

    Windows - 512.xx (although 472.xx works fine too)Ī few tips if you experience frequent LHR locks: The miner will calibrate the unlocker and the hashrate should go up to its normal level in about a minute after the miner displays calibration finished message. Make sure you remove any -lhr-tune settings you may have in your existing configuration.

  • (Linux) Memory temperature is not displayed on some GDDR6X cards.
  • Change default value of -lhr-autotune-mode parameter to down (used to be full).
  • ( ethash) Improve LHR unlock functionality (dual modes and autolykos2 LHR performance is unchanged)Įxpect about 78-79% in normal mode, and 75% in low power mode (see -lhr-low-power).
  • It will not work properly with older drivers. IMPORTANT: LHR unlocker requires 512.xx version of the driver on Windows, and 510.xx on Linux.
  • ( ethash, blake3) "Duplicate share" issue.
  • LHR unlocker is more stable compared to 0.25.12, infinite LHR lock loops should be solved now.
  • If you previously had -lhr-low-power in your config, the equivalent would be -lhr-low-power 1 (or "lhr-low-power": "1" in HiveOS). lhr-low-power 0,1,1,0 - the second and third GPUs will be working in low power mode.
  • (LHR) Low power mode can now be set for GPUs individually, e.g.
  • (LHR) Change -lhr-autotune-step-size default value to 0.1 (previously 0.5).
  • #Trex miner lhr full#

    lhr-autotune-interval 5:120, meaning that in -lhr-autotune-mode full mode the miner will be increasing LHR tune value every 5 minutes, and decreasing it as soon as it starts tripping LHR more frequently than once every two hours. (LHR) Allow setting "up" and "down" auto-tune intervals separately, e.g.LHR tune values aren't accurate, but once you've found a value that's stable for your GPU, you can set it manually with -lhr-tune and get consistent results across miner restarts. (LHR) Extend the new LHR unlock functionality to ETH+ALPH dual mining, and ERGO single mode.











    Trex miner lhr